New tyres for the Tri-ang Jump Jockey set

These new tyres are direct replacements for the original tyres fitted to the Tri-ang Jump Jockey sets, see above image. They are available in MAX Grip versions.

The new hand made MAX Grip tyres are unique to Scalextric Car Restorations and give the absolute maximum in performance at all times. Cornering and acceleration will all be at their maximum with these tyres. They give the very best performance possible on all track surfaces at all times. Simply put we have not yet discovered a better tyre for grip and race performance.

The MAX Grip tyres are hand moulded from 29 Shore A hardness rubber which is a very high grip material.

The tyres are smooth treaded and have a smooth tyre sidewall.

 

Dimension	Size (mm)
Outside Diameter	11.0
Inside Diameter	4.5
Overall Width	3.0

MAX Grip tyres from Scalextric Car Restorations

Fitting instructions for a Scalextric motor pinion gear - 9z

This process does not require specialist gear pullers or other tools

	Warm the gear to at least 30 degrees centigrade which will allow the plastic to stretch over the motor shaft without splitting. Simply holding the gear in a warm, closed hand for a few minutes will be sufficient or soak the gear in a container of warm water for a few minutes. Place the gear on a hard surface with the circular flange facing upwards.
	Gently push the motor shaft into the hole in the centre of the motor pinion gear. Use a constant gentle downward pressure. Continue until the motor shaft is right through the gear and touching the hard surface.
	Here the motor pinion gear is partly fitted. The shaft is flush with the face of the gear.
	Position the motor shaft over a void or hole in the hard surface. In this picture a gap in the jaws of the pliers is used. Again apply constant and gentle downward pressure to push the gear along the motor shaft and into the correct final position.
	Here the motor pinion gear can be seen in the correct final location along the motor shaft. The exact location may depend on your specific application.
Note: This pinion gear is used to service several different types of motor pinion gears fitted to several different Scalextric motors used over the years (decades). With some motors, especially those with poor or missing spines it may be necessary to reduce the diameter of the internal hole of the pinion gear. This will ensure the pinion gear is a good tight fit onto the motor shaft. To do this, use an opened up paper clip to smear a little superglue on the inside of the pinion gear. Allow the superglue 1 hour to set fully before a trail fitting the pinion gear to the the motor shaft. What you want is a good tight fit where the pinion gear will slide onto the motor shaft with a some effort. Add another smear of superglue onto the inside of the pinion gear if necessary. Allow this to dry fully for 1 hour before trail fitting again. Repeat as required.

Great ideas from Scalextric Car Restorations

Scalextric slot car Neodymium magnatraction magnet kit

Improved track performance with minimal effort.

These Scalextric spares Neodymium Iron Boron magnets have a gauss level which is typically 2 - 4 times higher than standard Alnico magnets. They are nickel-plated for improved corrosion resistance and appearance.

They are suitable for all slot cars; Artin, Ninco, SCX, Scalextric, SCX Scalextric, Tri-ang and many more.

This kit is great if you are not sure which Scalextric spares magnets would be best suited for your car.

 This kit contains:

Quantity	Description
2	Bar magnet 12mm x 6mm x 1.5mm (1/2" x 1/4" x 1/16" approx.)
2	Bar magnet 25mm x 6mm x 1.5mm (1" x 1/4" x 1/16" approx.)
1	Bar magnet 25mm x 6mm x 3mm (1/2" x 1/4" x 1/8" approx.)
2	Button magnet 8mm x 3mm (1/4" x 1/8" approx.)
2	Button magnet 8mm x 5mm (1/4" x 3/16" approx.)
1	Button magnet 10mm x 5mm (3/8" x 3/16" approx.)

Please see our Neodymium Magnet Safety Page for further information.

Our unique Magnet Downforce Calculator gives the magnetic attraction force for this magnet at given distances from the track. Ideal for locating the magnet.

Scalextroc spare parts from Scalextric Car Restorations.

Windscreen for the vintage Scalextric C69 Ferrari 250 GT

This windscreen is new and a direct replacement for the vintage Scalextric Ferrari 250 GT Berlinetta windscreen. This window moulding comprises all the windows, front, back and sides, for this Scalextric Ferrari Berlinetta model.
It is moulded in a fully clear material.

Ref.	Description
C69	Ferrari 250 GT Berlinetta
E4	Ferrari 250 GT Berlinetta

 Scalextric spare parts from Scalextric Car Restorations.

Windscreen for the vintage Scalextric C68 Aston Martin DB5

This windscreen is new and a direct replacement for the vintage Scalextric Aston Martin DB5 windscreen. This window moulding comprises all the windows, front, back and sides, for this Scalextric Aston Martin model.
It is moulded in a fully clear material.

Ref.	Description
C68	Aston Martin DB4
C97	Aston Martin DB4 007 **
E3	Aston Martin DB5 with lights
E5	Aston Martin DB5 Marshal's Car

** Some modeling skills are required to cut the sunroof aperture.

 Scalextric spare parts from Scalextric Car Restorations

Scalextric Aston Martin DB10 - C1336 Spectre set

This Scalextric C1336 Aston Martin DB10 - is new and unused, it is complete with all parts present and correct and has been removed from the Scalextric C1336 Spectre set.

The Aston Martin DB10 is fitted with its new and unused pick up braids. The body has no scratches or other marks and the factory applied decals are in perfect condition. The neodymium magnatraction magnet is fitted. The new tyres are in good, grippy condition. The white LED headlights illuminate well as do the red LED tail lights.
This unused Scalextric Aston Martin DB10 model is in wonderful condition and would add significant value to any collection. Simply put this car is just as it was when it left the factory.

Scalextric cars from Scalextric Car Restorations

Rear light lenses for the vintage Scalextric Ferrari 250 GT

These vintage Scalextric Ferrari 250 GT tail light lenses are direct replacements for the standard Scalextric items. The red translucent lenses are produced from a partially transparent material to allow the cars with lights to illuminate correctly.

Ref.	Description
C69	Ferrari 250 GT Berlinetta
E4	Ferrari 250 GT Berlinetta

 Scalextric spare parts from Scalextric Car Restorations

Rear light lenses for the vintage Scalextric Aston Martin DB4 and DB5

These vintage Scalextric Aston Martin DB4 and DB5 tail light lenses are direct replacements for the standard Scalextric items. The red translucent lenses are produced from a partially transparent red material to allow the cars with lights to illuminate correctly.

Ref.	Description
C68	Aston Martin DB4
C97	Aston Martin DB4 007
E3	Aston Martin DB5 with lights
E5	Aston Martin DB5 Marshal's Car

 Scalextric spare parts from Scalextric Car Restorations