Friday, 12 February 2016

MAX Grip tyres for your Scalextric cars

The design, manufacture and maintenance of MAX Grip tyres from Scalextric Car Restorations

Introduction

Scalextric Car Restorations has uniquely designed, developed and manufactures the MAX Grip range of tyres for the Scalextric range of cars. All the Scalextric tyre types and cars are covered by this range of tyres. This article explains how this was accomplished and the best way to look after your MAX Grip tyres.

The need for MAX Grip tyres

It became very clear early on that the tyres originally fitted to the Scalextric range of cars have a finite life. The tyres can simply wear out, they dry out and become hard, they can crack and in the worst case, fall apart. Also, with the introduction of the Sport track system the older Scalextric cars without a strong Magnatraction magnet couldn’t be used as the Sport track surface is much smoother than the classic track it replaced.
With these strong reasons it was necessary to introduce replacement tyres for the Scalextric range of cars. This new range of tyres also needed to give more track grip than the original tyres to allow the older Scalextric cars to be used on the Sport track without the addition of a Magnatraction magnet.
Another common problem is identifying which tyres are fitted to which cars. At the time of writing there are 137 different tyres available to fit 1675 different Scalextric models from 1960 to 2014, and they are all black and round. At the time “Which tyres fit my Scalextric car” was around half of the questions we used to receive at Scalextric Car Restorations. Some information was available via the Scalextric Service Sheets but very little information was available for the older cars.

Developing a Scalextric tyre database

At this time we already had a database of Scalextric cars produced based on the original Scalextric catalogues from catalogue 1 in 1960 up to the present. We simply added 2 new fields to the database, one for the front tyres and one for the rear tyres. For each new tyre identified a Master Sample was selected and stored, a 3 digit tyre identity code was assigned. This code was added to the database for each application. To populate the tyre database we used several methods:
  • During this period there were hundreds and hundreds of older Scalextric cars here at Scalextric Car Restorations so we were able to start to populate the database with the tyres fitted to these cars.
  • Reviewing all the published Scalextric Service Sheets allowed cars and tyre sets to be identified, cross reference and matched.
  • Tyre sets were purchased based on the Scalextric Service Sheets and the tyres identified.
  • Axle sets were purchased where replacement tyres weren’t available and the tyres identified.
  • Targeted Scalextric cars were purchased and their tyres identified.
  • Customers kindly sent their tyres to us to be reproduced in the MAX Grip material. These tyres where also identified.
  • All tyre applications were reviewed with crowd source data techniques where possible.
  • To date we have identified, coded and referenced 137 different tyres for the Scalextric cars produced from 1960 to 2014.
A live on-line version of this tyre database is in use on the Scalextric Car Restorations website and can be searched and browsed to find the right tyres for your Scalextric car. This database is known as the “Tyre finder” tool on the tyres section of the Scalextric Car Restorations website.

Developing the MAX Grip tyre

With the tyre database coming along and master samples of all the Scalextric tyres also underway, the MAX Grip tyre material was identified. Only the material was of concern as the shape and size of each replacement tyre was already given by the master sample. After much research a 29 Shore A hardness cold cure rubber material was identified and considered the best option. In addition the “stickiness” of this material could be adjusted in the tyre production process.
The tooling process was selected based on the expected volumes of tyres needed. A flexible mould material was selected that is compatible with the previously selected rubber tyre material and predicted production volumes.
A method to quickly and easily produce the production tools was developed and trailed. After a few refinements a reliable method to produce the production tools was established as well as a way to add tool identity markings.
With the material for the MAX Grip tyres selected some prototype tools were made and sample tyres produced. Several problems were identified and solved. This included completely filling the mould cavity, setting the right “stickiness” for the MAX Grip range of tyres and generally developing a reliable production process capable of producing tyres at the rate of around 1000 tyres every few months.
Each production tool has one cavity and can make one complete tyre at a time. Where higher production volumes are needed additional production tools are produced. Some of the higher volume tyres can have up to eight production tools.

Manufacturing the MAX Grip tyre

Production starts by weighing out the correct amount of raw material for the batch size, generally enough for 20 to 30 individual tyres in one batch. The material is thoroughly mixed and degassed in a vacuum chamber until all air bubbles are removed.
Each production MAX Grip tyre mould is filled by hand ensuring the mould cavity is completely filled with no air bubbles or voids. The Moulds used for the MAX Grip tyres are “closed moulds” which give 100% tyre detail including the inside tyre wall. Once the tyre is fully cured the mould is opened and the new tyre removed, any flash removed, the tyre is inspected and placed into stock. The production tool is inspected, cleaned and put ready for production use again. Production tools can be used 100s of times over to produce 100s of production MAX Grip tyres.
All MAX Grip tyres are produced by hand in the UK by Scalextric Car Restorations.

Maintaining MAX Grip tyres

MAX Grip tyres are designed to give the best overall levels of grip on both the Classic track surface and the Sport track surface. There are some points to take into account when using MAX Grip tyres:
  • MAX Grip tyres are sticky and will pick up dust and debris from the track surface. A specific test carried out was to race a Scalextric car fitted with MAX Grip tyres on a visibly dusty track. After several laps the performance of the car dropped away considerably, clean tyre track lines were visible on the track surface and the MAX Grip tyres were covered in dust.
  • The best grip is obtained when the MAX Grip tyre material is in contact with the plastic track surface. MAX Grip material to plastic gives very good grip, dust to dust gives very poor grip.
  • Maintaining MAX Grip tyres is really all about keeping them clean and free from dust, dirt and debris. To do this each tyre must be wiped over with a damp cloth prior to a race. The track should be kept clean, again use a damp cloth the lift the dust, dirt and debris from the track and kitchen paper or similar to dry the track immediately.
  • MAX Grip tyres are soft and will wear over time just like real car tyres.

Thursday, 11 February 2016

Vintage Scalextric trackside signs

These Vintage Scalextric trackside signs were used from the early 1960s. This sign shows the type of corner ahead on the race track. This Scalextric trackside sign can be fitted to all the Scalextric track produced from 1963 to the present day. They even fit the latest Sport Digital track pieces!!
These signs are moulded in white plastic with a clear printed label applied.
Overall dimensions:
  • Height: 38mm
  • Width: 33mm
  • Depth: 13mm
Scalextric trackside sign RH corner 45 degrees
Vintage Scalextric trackside sign – RH corner 45 degrees
Scalextric trackside sign LH corner 45 degrees
Vintage Scalextric trackside sign – LH corner 45 degrees
Scalextric trackside sign RH corner 90 degrees
Vintage Scalextric trackside sign – RH corner 90 degrees
Scalextric trackside sign LH corner 90 degrees
Vintage Scalextric trackside sign – LH corner 90 degrees
Scalextric trackside sign RH hairpin bend
Vintage Scalextric trackside sign – RH hairpin bend
Scalextric trackside sign LH hairpin bend
Vintage Scalextric trackside sign – LH hairpin bend
Scalextric trackside sign RH chicane
Vintage Scalextric trackside sign – RH chicane
Scalextric trackside sign LH chicane
Vintage Scalextric trackside sign – LH chicane
Scalextric trackside sign distance track narrows
Vintage Scalextric trackside sign – track narrows
Scalextric trackside sign distance 25
Vintage Scalextric trackside sign – distance 25
Scalextric trackside sign distance 50
Vintage Scalextric trackside sign – distance 50
Scalextric trackside sign distance 75
Vintage Scalextric trackside sign – distance 75
Scalextric trackside sign distance 100
Vintage Scalextric trackside sign – distance 100
Scalextric trackside sign distance 150
Vintage Scalextric trackside sign – distance 150
Scalextric trackside sign distance 200
Vintage Scalextric trackside sign – distance 200
Scalextric pitlane sign speed limit 30
Vintage Scalextric pit lane sign – speed limit 30
Scalextric pitlane sign speed limit 55
Vintage Scalextric pit lane sign – speed limit 55
Scalextric pitlane sign speed limit 60
Vintage Scalextric pit lane sign – speed limit 60
Scalextric pitlane sign speed limit 100
Vintage Scalextric pit lane sign – speed limit 100
Another great product from Scalextric Car Restorations

Compatibility between old and new Scalextric cars and Scalextric track – updated

Use your new Scalextric cars on your old Scalextric track and your old Scalextric cars on your new Scalextric track with these simple hints and tips

Abstract

Scalextric (in one form or other) have been producing Scalextric track and Scalextric cars since the late 1950s and over this time several different standards have been used. This is for both the cars and the track. However, some of the basic principles have remained the same. The track has a slot and two conductor rails on each side. The cars use the slot to guide them around the layout and electrical contacts to touch the conductor rails. Finally the system voltage and current requirement are similar too.
This article explains what is compatible from old to new and what is not, and what you can do about it.

Introduction

Over the years the track has a slot that has broadly remained unchanged, the cars have a pin or blade that runs in this slot to guide the car around the track. Each side of the slot there are two electrical conductor rails who’s dimensions have broadly remained unchanged. The Scalextric cars then have 2 contacts, usually made from flat braided wire that touch each conductor to carry the electric current into the car. The nominal electrical voltage has remained at 12 Volts to 14 Volts for both the power systems and the motors in the cars and the current draw has remained similar too.
This article considers the compatibility of cars and track produced from 1960 to the present day (2013).

Scalextric Track

The Scalextric track pieces provide several key requirements:
  • A known surface for the cars to race on.
  • A slot in order to guide the cars around the circuit.
  • A method of supplying electrical current to the motors in the cars.
Mechanically the Scalextric track may appear quite different from old to new and had several different standards over the years. The very first track pieces produced were known as “rubber track” and wasn’t well designed with poor fixings between the track pieces. In 1963 a plastic track was introduced with good positive fixings between the track pieces. This plastic track is now often referred to as the Classic Scalextric track. In 2002 the track design changed to the Scalextric Sport track design which had an improved fixing method between the track pieces. At the time of witting in 2013, this is the current track design.
Classic Scalextric track
Throughout this period the slot in the track and the conductor rails have remained largely unchanged in specification which means the key interface to the Scalextric car has also remained unchanged. One area of difference is that the Classic Scalextric track range offered many track pieces that contained obstacles such as chicanes, hay bails, backed curves and even rocks. None of these are available to the same degree with the Scalextric Sport track system.
Further, the Classic Scalextric track range had a deep graining on the surface giving the car tyres good mechanical grip for cornering and acceleration. With the introduction of Magnatraction the Sport track range didn’t need such heavy graining and so has a much lighter surface graining giving a smoother appearance and feel to the track surface.
  • 1960 to 1962: Rubber track.
  • 1963 to 2001: Classic track.
  • 2002 to present: Sport track.
Classic Scalextric track and Sport Scalextric track use different clipping arrangements to connect together. There is a special piece of converter track that can be used to join together Classic Scalextric tack and Sport Scalextric track.

Scalextric Cars

The Scalextric cars have changed little in their basic layout throughout this time. There is a method at the front of the cars to locate or guide them around the track which is either in the shape of a blade or a pin. The blade guides need to rotate in the underside of the Scalextric car to allow the car to take corners while the pin guides tend to be fixed and not rotate. With pin guides the pin is narrow enough to rotate in the slot itself.
Each side of the guide blade or pin there are two metal conductors, usually in the form of flat woven metal braids. These braids rub along the conductor rails providing the necessary two electrical contacts between the track and the car. The motor is then connected to the braids with short lengths of wire. The motor drives the rear axle via a simple gear mechanism which in turn drives the car forward.
Scalextric Javelin model from 1970
Older Scalextric cars tended to have plenty of up/down movement of their front axles and sometimes the front wheels were no where near the track surface. The front of these cars rests solely on the guide and braids. Later Scalextric cars have removed this movement with most running fixed front axles where the front wheels run on the track surface. This is much more realistic as the front wheels rotate as the car moves along the track layout.
In more recent times Scalextric Digital has been introduced. In Scalextric Digital cars there is a small electric circuit (chip) fitted to the car where power from the track goes into the chip and the output from the chip drives the motor. The chip also drives an LED which points downward and which communicates to track pieces to change lanes.

Electrical

The basic electrical specification has remained unchanged from 1960 to the present. The analogue system voltage is 12 Volts to 14 Volts with a series resistive control method. The electrical current drawn by the motors has reduced over the years with the introduction of more efficient motors.
Scalextric Digital uses a completely different way to control the cars. Constant power is supplied to the whole track layout and the cars are controlled with digital signals that again go around the whole circuit.

Compatibility – old cars on new track

There are several factors concerning the use of old Scalextric cars on new Scalextric track. The first of which relates to the change in the surface grain from Classic to Sport track. The older Scalextric cars without Magnatraction will have little mechanical grip from their rear tyres making acceleration and in particular cornering difficult. This can be overcome by fitting Magnatraction magnets and/or MAX Grip tyres. With some ingenuity magnets can be fitted to all of the older Scalextric cars and MAX Grip tyres are available for all the older Scalextric cars too.
The other difficulty concerns the pin guides. The later track layouts used obstacles such as crossovers and the modern Scalextric Digital layouts use lane change pieces or points in the railway vernacular. Essentially, the pin guide doesn’t provide any directional stability which means as a car with a pin guide passes over a crossover piece of track it stands a good chance of moving to the wrong lane or slot. To use Scalextric cars with pin guides on later layouts either the lane change or crossover pieces of track need to be removed from the layout or the cars can be converted to use guide blades instead of pins.
The older Scalextric motors tend to consume more electrical current than the newer Scalextric cars. As such the newer power supplies associated with newer Scalextric layouts may not provide sufficient current to allow two older Scalextric cars to race at full power.
Non digital Scalextric cars cannot be used on the Scalextric Digital system as the electrical systems are not compatible. NOTE, a traditional analogue Scalextric car may sustain permanent damage if placed onto a live Scalextric Sport track layout.

Compatibility – new cars on old track

On the whole it is easier to operate new Scalextric cars on the older Scalextric track layouts. Electrically they consume less current and all have guides blades rather than pins. The key problem concerns the fixed front axle as this prevents many of the older obstacles from being used. As the front wheels traverse an obstacle they lift the contact braids away from the conductor rails on the track and the car stops. Obstacles that cannot be used with new Scalextric cars include:
  • Banked curves.
  • Hump backed bridges.
  • Bumpy or rocky track.
Additionally, because of the front axle the new Scalextric cars need a very flat surface on which to operate. Old warped, bent or out of shape track pieces may cause problems for the newer Scalextric cars.
Scalextric cars fitted with a Scalextric Digital chip can be used on analogue layouts.

Compatibility – Analogue and Digital

There are two types of control mechanisms used by Scalextric, these are Analogue and Digital. The Analogue control system is the traditional method which uses a basic resistive winding of wire in the hand controller to control the D.C. voltage sent to the track and car. In the car the wires from the braids connect directly to the D.C. motor.
The Digital system uses frequent digital data messages from the controller to a microprocessor fitted to the car. The track has a permanent A.C. power supply which also goes to the microprocessor in the car. The microprocessor in the car then controls a Pulse Width Modulated (PWM) power feed to the motor based on the digital data messages from the controller. Therefore there is no direct connection from the track to the motor in a digital car.
Digital cars will work perfectly normally on an analogue power system but analogue cars do not work the Digital power system. Analogue cars may be permanently damaged by the Digital power system.

General

On the whole there is very good compatibility between the old and new Scalextric cars and Scalextric track. Newer Scalextric cars can run well on older Scalextric layouts as long as the layout is flat and contains no sudden changes in height such as rocks or banked curves. Older cars may need some updates to run well on the newer track especially concerning grip. Scalextric cars with pin guides need to avoid layouts with any form of crossover or lane change method.

About the author:

Gary Harding has been working with Scalextric cars for over 35 years and now operates Scalextric Car Restorations in the UK. Scalextric Car Restorations is a Worldwide internet based business that offers for sale high quality Scalextric cars and Scalextric parts from the 1960s to the present day. All the restoration work is carried out to the highest standards with the highest quality parts available. Only the best cars are selected and the final result is a car that is genuinely like new.
Further help and advice relating to this article or Scalextric cars in general can be found at:
http://www.scalextric-car.co.uk

How to service the RX motor in your Scalextric car – updated

Maintain your Scalextric car’s RX motor with these simple hints and tips

Abstract

The earlier Scalextric cars produced in the 1960s were fitted with open frame motors the most common of which is known as the RX motor. This motor was also fitted to many of the Hornby locomotives of the period. This article shows how an RX motor can be serviced in a methodical way by considering the mechanical, electrical and magnetic aspects of the motor.
Scalextric RX motor

Introduction

The RX motor was fitted to most Scalextric cars from the 1960s. In order for your Scalextric car’s RX motor to give the best possible performance it has to be in the best possible health. Effectively giving the maximum torque for the electrical power available to it. For any electrical motor to give its best 3 key areas need to be considered; the mechanical condition of the motor, the electrical condition of the motor and the magnetic condition of the motor.

Mechanical

Mechanically the RX motor needs to be in the best condition possible to ensure that no energy is lost and the motor can transfer all of the generated torque to the rear axle. To do this several areas need to be reviewed:
  • Firstly check and ensure that all the parts are present and undamaged. All missing or damaged parts must must be replaced.
  • Check and ensure the motor armature spins freely with no rubbing or tight spots. This could be caused by missing or damaged bearings or a damaged motor housing.
  • Review the motor pinion gear and ensure all the gear teeth are in good condition. Replace the pinion gear if gear teeth damage is found.
  • Add a drop of oil to each of the bearing felt pads.
  • Ensure the brush spring sleeve is present and in good condition. Replace if necessary.

Electrical

There are many electrical connections and contacts used on the RX motor. Each of these must be in good condition to ensure the best performance of the motor. To do this several areas need to be reviewed:
  • Firstly check and ensure that the solder joint between the wire from the pick-up brush and the eyelet that fits over the brush spring sleeve is complete and sound. Replace or remake this joint if any of the wire strands are broken or not making contact.
  • Inspect the eyelet for any dirt or metal oxides that may have formed over the years. Clean the brush spring back to clean shiny metal where it contacts the motor brush.
  • Inspect the brush spring for any dirt or metal oxides that may have formed over the years. Clean the brush spring back to clean shiny metal where it contacts the motor brush and the screw that secures the magnet.
  • Inspect and clean the motor brushes removing any dirt, oil and carbon deposits. Ensure the carbon block is present and securely attached to the brass strip. Clean the motor brushes back to clean shiny metal where they contact the brush spring and eyelet.
  • Remove any dirt, oil and carbon deposits from between the commutator segments of the armature.
  • Remove any dirt, oil and carbon deposits from the commutator.
  • Check the three solder joints that secure the armature windings to the commutator, remake these joints if necessary.
  • The electrical connections for a car with an RX motor are:
    • Contact: Track braid to track rail
    • Contact: Braid contact to track braid
    • Solder joint: Wire to braid contact
    • Solder joint: Motor brush sleeve to wire
    • Contact: Motor brush to motor brush sleeve
    • Solder joint: Motor brush carbon block to motor brush
    • Contact: Commutator to motor brush carbon block
    • Solder joint: Armature wire to commutator
    • Solder joint: Armature wire to commutator
    • Contact: Commutator to motor brush carbon block
    • Solder joint: Motor brush carbon block to motor brush
    • Contact: Motor brush to brush spring
    • Contact: Brush spring brass bolt
    • Contact: Brass bolt to eyelet
    • Solder joint: Eyelet to wire
    • Solder joint: Wire to braid contact
    • Contact: Braid contact to track braid
    • Contact: Track braid to track rail

Magnetic

The magnetic field used by the RX motor is provided by a permanent magnet at the rear of the motor. The magnetic field reaches the outside of the armature by the use of steel plates that are also used as the housing for the motor. To ensure the magnetic circuit is maintained the RX motor uses various materials to ensure the magnetic field is not reduced. Over time the magnet can lose some of its magnet field strength thereby reducing the motor’s torque and top speed. A replacement Neodymium magnet is available to restore and improve the RX motor’s performance.
  • Ensure the magnet is secured by the correct brass screw.
  • Ensure both the steel housing plates make good tight contact with the magnet.
  • Ensure the aluminum plate adjacent to the magnet is fitted correctly.
  • Ensure the brass plate at the commutator end of the motor is fitted correctly.

General

Through experience we have found that some RX motors still do not perform well even with all of these checks completed. This may be caused by a weak magnet or internally damaged armature windings. These faults are outside the scope of this article. There are many other possible faults with the earlier cars with the open frame motors. This is intended as a simple fault finding guide only. If the information above does not resolve the fault then contact us for further information.

About the author:

Gary Harding has been working with Scalextric cars for over 30 years and now operates Scalextric Car Restorations in the UK. Scalextric Car Restorations is a Worldwide internet based business that offers for sale high quality Scalextric cars and Scalextric parts from the 1960s to the present day. All the restoration work is carried out to the highest standards with the highest quality parts available. Only the best cars are selected and the final result is a car that is genuinely like new.
Further help and advice relating to this article or Scalextric cars in general can be found at:
http://www.scalextric-car.co.uk

Wednesday, 10 February 2016

Scalextric track maintenance

In this article we are looking into Scalextric track maintenance. There are several areas where your Scalextric track can cause problems, these are:
  • Corroded, oxidised and dull track rails
  • Bent or warped track pieces
  • Poor electrical connections
  • Dirty and dusty track
Corroded, oxidised and dull track rails
Polishing pad for Scalextric track
Over time and especially if your Scalextric track is stored in a damp environment, the steel rails of your Scalextric track can become discoloured and slightly rough as the electroplated surface corrodes. This slows down your Scalextric cars and wears out the Scalextric car braids more quickly. In severe cases brown rust may be present of the underlying steel rail.
To prevent this simply polish the Scalextric track rails back to a smooth clean surface with the track polishing pads. These will do the job more quickly and more effectively than any other method we know of.
There are three grades of track polishing pad available, coarse, medium and fine. The different grades are used for different purposes.
Coarse:
The coarse grade pad is used to renovate track rails with rust marks and is not intended for regular use. Use the fine grade pad or medium grade pad after the coarse grade pad to complete the renovation of your Scalextric track rails.

Medium:
The medium grade pad is for use to renovate moderately tarnished track rails and is not intended for regular use.

Fine:
The fine grade pad is designed for regular use to remove dust, debris and light tarnish from the track rails. It is also used after the coarse grade polishing pad to give a smooth running surface.

Bent or warped track pieces
Scalextric track has a tendency to bend or warp over time. This may have many causes among which are people stepping on the track laid on the floor and perhaps the way that the classic track clips together doesn’t help.
Scalextric track C160 standard straight
Warped track works well enough but can give your Scalextric cars a very bumpy ride, especially down the long straight. Also, the newer Scalextric cars will struggle as they are far more likely to ground out on a bumpy Scalextric track layout.
The answer is to shape the Scalextric track pieces back to level. To do this simply reverse the bend in the track a little at a time and a bend at a time until the track is visibly flat again.
The most common problem then is that the vertical sides of the steel track rail bend outwards and block the slot in the track. This is remedied by pushing the bulge back out of the way with a flat blade screwdriver. There you have it, flat, level Scalextric track that works for new Scalextric cars as well as your older Scalextric cars.
Poor electrical connections
An odd phenomenon that can occur with a Scalextric track layout is that over time part of the track layout looses power. The Scalextric cars run great near to the track power base or where the power is connected to the track but slow down away from the power connection point.
This effect can happen several weeks or even several months after a circuit has been constructed and not usually right away. We are not too sure of the exact mechanism that causes this but we know it’s the joints between the track pieces that introduce a high resistance to electrical current.
There are 2 readily used fixes for this problem with Scalextric tracks; one is to regularly take up the track and relay it with the track pieces in different locations, strange but true. The second is to run a Scalextric track power booster cable around the track and make connections to the track every couple of meters or so.
Scalextric track power booster cable
If your Scalextric track layout is permanent then you’ll be best advised to make an electrical connection to every track piece with the Scalextric track power booster cable. The best type of connection is a solder joint.
Dirty and dusty track
The only form of grip for a Scalextric car is between the 2 rear tyres and the track surface. Grip provides the acceleration force, deceleration force and the cornering force too. Physics tells us that the amount of friction is proportional to the amount of force pushing the surfaces together and the friction between those surfaces.
Force = Friction x Normal force
To give the most grip the track surface has to be as clean as possible. So, how do you keep your track dust free? The simplest way is to wipe your Scalextric track over with a damp (NOT wet) cloth and dry immediately. This will remove the dust and debris and give you the best possible grip from your Scalextric track. Ensure the track is dry before you go racing.
Another great solution from Scalextric Car Restorations

Digital conversion of Scalextric C2808 Range Rover Police car

This Scalextric Digital conversion is made more complicated than normal because of the working Police lights and siren.

All the Scalextric Police cars can be converted to Digital using this process.

Digital Conversion C2808 Range Rover Police
This is the Scalextric C2808 Range Rover Police car as delivered by the customer. The car is new and unused. Now all it needs is a digital chip fitting….
However, this is a Police car with working lights and a siren. The electronics that power the lights and siren is not compatible with Scalextric Digital as the power feed needed is not provided by the Digital track or the Digital chip output to the Scalextric motor.
As you’ll see later in this conversion we fit a special power adaptor to ensure the lights and siren all work correctly after the Digital conversion.
Digital Conversion C2808 Range Rover Police Here the Range Rover has been opened up to reveal the contents. From left to right you can see the following; steel weight, rear axle, motor, electronic Printed Circuit Board (PCB) for the lights and siren, guide fixing screw, front axle and lastly another steel weight right at the front. In this arrangement the power from the track goes directly to the PCB and the wires for the motor also go to the PCB. There is a small piece of electronics between the track and motor to ensure the motor is always driven in the right direction.
This electronics is known as a bridge rectifier and is used for the lights and siren too. Again, to ensure the correct polarity of Direct Current (DC) is fed to the electronics.
Digital Conversion C2808 Range Rover Police In this picture you can see we have fitted the Scalextric Digital chip between the motor and the existing PCB. The Digital chip is secured in position with a small amount of superglue. We do this before we remove any components so we can be certain that all the parts will fit in position once the car is reassembled.
We have used the Scalextric Digital C7005 In-Car Microprocessor.
Digital Conversion C2808 Range Rover Police A close up of the Scalextric Digital C7005 In-Car Microprocessor in position with all the other components still in place.
Digital Conversion C2808 Range Rover Police Now we have removed the electronic PCB to give the access need to complete the fitment of the Digital chip. We unsoldered the wires from the motor and the guide contacts. That’s four wires in total and two screws to remove the PCB from the chassis. All the wires from the PCB into the upper half of the body are untouched and remain connected.
Digital Conversion C2808 Range Rover Police Here the Infra Red LED is fitted into the existing hole in the chassis just behind the guide blade. A tiny drop of superglue keeps the LED in position. The wires are also soldered to the motor in the same position as the original wires from the PCB.
We’ve also added a piece of insulation tape on the top and side of the motor to ensure nothing can short out which would damage the Digital chip.
Digital Conversion C2808 Range Rover Police In this picture the installation of the Digital chip is complete and the wiring tidied up This is now a fully working Scalextric Digital conversion but without the working lights and siren.
Digital Conversion C2808 Range Rover Police The motor feed wires from the original PCB are trimmed off as they are no longer needed and could short out if left as they were. The original PCB is then refitted to the chassis with only two wires to connect. These were the feed wires that originally connected to the guide blade contact.
Digital Conversion C2808 Range Rover Police As stated at the start of this article the feed wires for the siren and lights cannot be connected to the track connections or the motor connections directly. For the technical out there, the PCB needs analogue DC 6 Volts to 14 Volts. The Digital track provides AC and the drive to the motor from the Digital chip is a Pulse Width Modulated (PWM) signal.
Therefore, we use this unique power adaptor.
Digital Conversion C2808 Range Rover Police The power adaptor is fitted at the very rear of the chassis behind the metal weight and secured with a drop of superglue. The power adaptor has four wires, 2 are the power feed in from the motor and two are the corrected power output to the PCB for the lights and siren.
Red and black wires to the motor tags and green and black output wires to the PCB.
Digital Conversion C2808 Range Rover Police Close up of the power adaptor in location. The power adaptor takes in the PWM signal from the Digital chip to the motor and creates stable analogue DC 6 Volts to 14 Volts just like the PCB needs.
Digital Conversion C2808 Range Rover Police In this picture the power adaptor has been connected up to the car and all the conversion work inside the car is complete.
Digital Conversion C2808 Range Rover Police Back together and there’s no way to know that this Scalextric C2808 Range Rover Police car has been converted to digital. Everything works just as it used to including the lights and siren on both the traditional analogue layout as well as on a digital track.
Digital Conversion C2808 Range Rover Police The finished car from below. Just the LED to see from this view.
Digital Conversion C2808 Range Rover Police A close up of the LED just behind the guide blade
Another great article from Scalectric Car Restorations

Windscreen for Scalextric C71 and C96 Auto Union C Type

Announcing the re-manufacture of the windscreen for the Vintage Scalextric C71 and C96 Auto Union C Type.  This  Scalextric Auto Union C Type windscreen is new and is a direct replacement for the standard Scalextric item.  It is moulded in a crystal clear material.
This windscren may also fit the Pink Kar version of the Auto Union C Type.
Windscreen for Scalextric C71 and C96 Auto Union C Type
Scalextric C96 Auto Union C Type
Another great replacement Scalextric part from Scalextreic Car Restorations